Available in Simulated Aluminum, Black Anodized Aluminum
and Gloss Black OEM material

Where did the GM logos go??
We have been contacted by General Motors legal department concerning the use of trademarked logos on the items we sell, and they have demanded that we no longer advertise any items that have a GM trademark. The basis of trademark law is the issue of "confusion", that our customers may believe that they are buying a licensed genuine GM item.
We have always made it clear that
we do not make imitations of any GM parts.
But we don't have the resources to litigate this issue, so we must comply with their demands. Therefore, we do not show any pictures of an item with a trademarked GM logo. We of course as always offer custom engraving on most items, and we have come up with a few "generic" logos that are "acceptable".

HOWEVER, AND THIS IS IMPORTANT: While the law may say that we cannot show photos or renditions of trademarked logos, there is NO LAW that prevents us from supplying you with anything you want for your vehicle, including any additional artwork or graphics. Therefore, if there's any type of artwork or graphic you want added to your item and it's not on our website, just ASK, or provide us with some artwork of what you'd like. We will gladly meet your request, if possible. Please note that a small extra nominal charge may apply depending on what you request.

(CLICK ON PHOTOS TO SEE FULL SIZE!)

Special note on GLOSS Black OEM Material

Our GLOSS black console overlays are identical to the material used by the factory for the main dash and radio area.  Now your console can match your dash panels.  This material is highly susceptible to scratching so this would be recommended for show cars only.  Engraving of logos on this material is more expensive due to the engraving technique involved.  Material is engraved from the back and then hand painted. 

Our console overlays consist of the 3 panels that cover the top surface of the console. The large piece around the shifter, the ashtray cover and the small strip to the rear of the ashtray.  You can install them directly over the existing stock overlays if they are in good shape.  (NO BUBBLES OR TEARS IN THE MATERIAL) Or you can easily remove the factory overlays and then install ours. NOTE! The shifter handle must be removed in order to install the main panel.  This is real easy to do - pull the c-clip at the base of the handle out and then pull the handle up. The overlays are held in place with high quality double-backed tape that is already applied to the panels.  Just peel the backing and install!

Black anodized sets are made from .031" thick anodized brushed aluminum, and really look sharp!   All prices are listed below in the drop down menu. Extra lettering engravings are possible for the small piece behind the ashtray cover.   

CUSTOM ENGRAVING IS AVAILABLE ON 3 DIFFERENT AREAS ON THE OVERLAY.  TO ALLEVIATE ANY CONFUSION ABOUT LOGO PLACEMENT, PLEASE REFER TO THE ILLUSTRATION BELOW!

THIS ITEM IS AN OVERLAY ONLY!
DOES NOT INCLUDE ANY FACTORY PARTS.

PLEASE READ BEFORE ORDERING!

Below is the various shifters we have made overlays for.
Select the one you want from the appropriate ordering box below.
IMPORTANT!  When ordering an overlay for an aftermarket shifter, let us know if you have a 3 or 4 speed automatic and whether you have a stock or reverse pattern shifter so the engraving is done properly!  If you don't tell us we will assume that you have a four speed automatic and stock shift pattern.  Not responsible if you don't tell us!

NOW AVAILABLE!

Have you converted your Turbo Regal to the Hurst Lightning Rods shifter setup?  We are now offering console kits for these conversions. Custom ashtray plate engraving is optional as well as engraving on the small strip to the rear of the ashtray. Click on the drop down menu to see your choices. Available only in simulated aluminum or black anodized aluminum finishes.  Click here to go to the Olds Console page to see what our Lightning Rods consoles look like.  The ones we make for the Buick conversion do NOT have the screw holes as they are held on with double sided tape. IMPORTANT!  Since installing the Lightning Rods in a Turbo Regal is a custom setup, you need to print out the template we have made up to see if it will work for your installation.  Get the template by clicking here!  Let us know if it needs any adjustments to fit properly.